anyone know what light is in the head board? i can not stand opening a door at night and get blinded by the white headboard light. i wan to replace it with a red light.

havent had time to mess with it yet to figure out how to take it off. was wonderng if anyone knew the replacement part number for the bulb

I copied this from the owners manual. Hope this is what you need.

LIGHT BULBS — Interior Bulb Number

Front Courtesy/Reading Lights . . . . . . . . . . 578/W5W
Center Courtesy/Reading Lights . . . . . . . . . 578/W5W
Visor Vanity Lights . . . . . . . . . . . . . . . . . . . . . A6220
Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194
Shift Indicator Light . . . . . . . . . . . . . . . . . JKLE14140
Rear Compartment (Trunk) Light . . . . . . . . . . . . . 579

Take some before and after pics and post them if you can. :) I prefer the white led's (i think they look cool) but would be interested in seeing other ideas. :)

I just turn the interior lights to off and they never come on.

anyone know where i can find 578's in red?

Here are some links, hopefully they will help :)

http://www.superbrightleds.com/led_prods.htm
http://www.oznium.com/prewired-leds
http://autolumination.com
http://www.bulbman.com/
http://www.slickcar.com
http://www.streetbeatcustoms.com
http://streetglow.com/site/index.php
http://www.customdynamics.com/index.htm
http://superlumination.com/

none of those links helped.

even looked around, seems no one sells 578's

is there a dift mdel number to use?

none of those links helped.

even looked around, seems no one sells 578's

is there a dift mdel number to use?


Look at the superlumination link again. They show a link for 578 festoon's but when you visit that link none of them specifically say "578". Doesn't mean they aren't or wont work, and it leads me to believe there is a slightly different number for the same bulb.

What I would do is pull a bulb, measure it and then try to match it up on their site with a picture and the size. You should be able to fins something that works.

Aside from that, you may be able to remove the existing led from the package its in and replace it with another led from a place like www.digikey.com (http://www.digikey.com) . I haven't actually looked to see what would all be involved in something like that though.

I'm a newbie and may be in the wrong thread, if so I apologize and please send me elsewhere. I've recently purchased a 2008 Avenger, but the dome light is broken. I picked up a used one with reading lights hoping to upgrade. However my avenger has only 2 wires (brn/wht in mid slot, Blk on one side and blank on 3rd slot). The used dome light with reading lites & switches has 3 wires.(Blk on mid slot, grn/red on one side and blu/blk on other side). I need help. My thought is put Black from 2-wire Avenger in middle with spliter of brn/wht to the 2 outside posts on the replacement connector? thanks in advance.

2 wire:
Hot = brn/wht
Ground = Black

used dome light with reading lites & switches has 3 wires.(Blk on mid slot, grn/red on one side and blu/blk on other side

grn/red = hot
blk/blue = hot
Blk in mid slot = ground

These are my guesses.

I would tie brn/wht to grn/red and blk/blue and tie black to Black.

My bet though is that you will probably only get lights when you open the door or turn on the dome. You would probably need a new always on Hot to get reading lights. But again, Im guessing